Teroson SB S-3000 - 1 L bright spray against stones

Product detailed description

Terotex Super 3000 is a highly viscous, sprayable coating material containing solvents based on synthetic resin. The product is fast-drying and can be quickly overcoated. After complete drying, the coating exhibits resistance to abrasion, corrosion protection and aging. The dry film has good adhesion to raw and painted sheet metal, as well as to plastic parts or sheets that have been treated with a primer or filler. Terotex Super 3000 can be overcoated with classic car paints (both conventional and water-based paints). Drying in a drying oven is possible without problems for both painted and unpainted parts. After complete drying, the coating can be sanded / sandblasted. It has a high durability and excellent properties for spraying. This allows almost any surface to be covered.

Application areas:

Terotex Super 3000 is used to protect visible parts of the bodywork against abrasion caused by flying gravel, salt and moisture and allows the structure of the original surface to be created on the repaired area. Not suitable for elastic materials.

Technical data:

• Color: light beige
• Smell: aromatic
• Consistency: viscous liquid
• Density: approx. 1.2 approx. 59%
• Solvent / cleaner: Cleaner – D
• Surface drying: 2 – 3 hours
• Complete drying: overnight
• Application temperature: 10°C – 25°C
• Operating temperature: 80°C
• Short-term (up to 1 hour): 100°C

Preparation:

The surface must be clean, dry and free of rust, petroleum jelly, dust and other impurities. Thoroughly cover the surface that is not intended to be painted with Terotex Super 3000. You can improve the adhesion of the product by roughening the surface with sandpaper.

Application:

Terotex Super 3000 is applied using a Teroson - UBS application gun from 1l cans. An application pressure of 4 - 5 bar is recommended. Shake the can thoroughly before use. Do not leave the can open so that the material does not dry out (and does not form a crust on the surface). A nice surface structure can be obtained using classic application guns that are commonly available in paint stores. The thickness of the Terotex Super 3000 layer should not exceed 1 mm. The maximum thickness of the product layer can be obtained by applying it in several application cycles. After applying the Terotex Super 3000 structural coating, the surface can be painted with the so-called "wet on wet" (after about 15 minutes) with classic car paints (regular and water-based paints). For best results, paint up to 6 hours after applying the paint. After complete drying, treat the paint as if it were plastic before painting - i.e. it is recommended to sand the surface and use a suitable primer.

Drying:

After painting so-called "wet on wet", the drying process can be accelerated without complications by using a drying oven (temperature 60°C). If the painting process requires the use of infrared drying, leave the Terotex Super 3000 layer to air dry for at least 3 hours before painting. If Terotex Super 3000 is exposed to infrared radiation immediately, blisters will form.

Painting plastics:

To create the original structure of a plastic bumper (see Teroson plastic repair kit), mix Terotex Super 3000 with a two-component water-based paint). The mixing ratio should not exceed 50 vol. % paint and hardener. It is possible to add a small amount of the original paint for slight tinting to obtain a matt appearance.

By using different application pressures, distances from the substrate and application nozzles, it is possible to obtain different surface structures. Before applying Terotex Super 3000 to plastic parts, Terokal – 150 plastic primer must be used.

Cleaning:

Remove spills immediately with Cleaner – D. Already dried Terotex Super 3000 can only be removed mechanically. Warning: Cleaner – D damages some plastics and coatings!

Instructions for assembly, disassembly and cleaning can be found in the product data sheet. Safety data sheet Teroson Terotex Super 3000 on request.

Henkel - Teroson Terotex Super 3000 - IDH: 782601 - Catalog number: 18277R


Teroson Terotex Super 3000 light - 1 LTerotex Super 3000Terotex Super 3000

TEROSON® SB S3 synthetic resin and can be used for spot repairs. It is ideal for producing all different types of factory textures. The product is overpaintable and has good abrasion resistance. Easy to apply with filling or paint guns, TEROSON® UBC AIR GUN or TEROSON® UBC AIR GUN WITH CAN. TEROSON® VR 10 is recommended for surface preparation.

TEROSON SB S3000
Bodywork repairs - stone chip protection product. Synthetic resin, abrasion resistant, overpaintable.
TEROSON® SB S3000 is a stone chip protection product based on synthetic resin and can be used for spot repairs. It is ideal for producing all different types of factory textures. The product is overpaintable and has good abrasion resistance. Easy to apply with filling or spray guns, TEROSON® UBC AIR GUN or TEROSON® UBC AIR GUN WITH CAN. TEROSON® VR 10 is recommended for surface preparation.