Sicomet 40 - 20 g instant glue

Product detailed description

Sicomet 40 (IDH: 277438 / 1437113 / 38840015)

Sicomet 40 is a very fast-curing instant adhesive based on ethyl cyanoacrylate with low viscosity. It is primarily intended for bonding plastics, rubber and metals. Thanks to its capillary effect, it can penetrate even the smallest joints, which makes it ideal for stabilizing and sealing porous surfaces or for filling small ventilation holes in rubber and plastics. The product can be used in environments with operating temperatures up to 80°C and can withstand temperatures up to 100°C for short periods. temperature

Technical parameters:

• Chemical type: Ethyl cyanoacrylate
• Appearance (uncured): Clear, colorless
• Viscosity:
  • Rheometer (conical plate) at 25°C: 2 to 4 mPa·s (cP)
  <0>Bro (cP), spindle 3, 100 rpm
• Density (ISO 12185): 1.05 to 1.1 g/cm?
• Mechanism Curing: Air humidity
• Temperature resistance: Up to 80°C (Up to 80°C) (short term)
• Fixation time: Depends on substrate, usually faster on metals than on rubbers or plastics
• Full cure: 24 hours for maximum resistance to chemicals and solvents

Application:

• Assembly of electronic devices
• Bonding of components in the automotive industry
• Sealing of porous surfaces in rubber and plastic parts
• Joining plastic components in household appliances or consumer goods
• Assembly of medical devices

  Use for application:

  • Surface preparation: For thorough degreasing and remove dirt, use Loctite SF 7061 cleaner, which ensures gentle but effective cleaning. hydrocarbons.

  • Removing seals and adhesive residues:If you need to remove old seals, adhesives or other materials from a bonded surface, Loctite SF 7200 is the ideal choice. Its application is simple - just apply and leave to act, which will easily peel off the material. Be careful with painted and plastic parts. Sicomet Debonder or Sicomet Hi Speed BS activator The activator accelerates curing on passive

    Precision applications: for precise application, application needles can be used. There are a variety of needle types, so we recommend this 24-piece test set of dispensing needles, so you can best find out which type it is. There are three basic lines PPC, PPF, SSS and the color of the applicator needle indicates the inner diameter of the needle. Loctite SF 7840 . This universal water-based cleaner is biodegradable and is ideal for effective cleaning of various surfaces without damaging the material.

  • Cleaning hands after work: After completing the application, use Loctite SF 7850 , which is suitable for effective hand cleaning. This biodegradable cleaner removes oils, greases and other contaminants.

    Typical properties:

    • Bond strength: High bond strength to a variety of materials, especially plastics and metals
    • Performance on metals: Excellent adhesion to a variety of metals, especially with proper surface preparation
    • porous plastics such as polyethylene or polypropylene (with or without primer)

    Yield: A typical yield of one 20g bottle is sufficient to bond hundreds of small parts, however actual consumption will vary depending on the size of the bonded areas and the method. properties:

    • Tensile strength: High initial strength, especially when fully cured after 24 hours
    • Shear strength: Excellent on plastics and rubbers
    • Resistance to Chemicals: Good resistance to a variety of chemicalsInstructions for use:
      1. Clean the bonded surfaces with a cleaner such as LOCTITE SF 7063 to remove oil, dust or dirt.
      2. Apply a small amount of Sicomet 40 to one area. together and hold firmly for a few seconds until the adhesive sets.
      3. Full bond strength will be achieved in 24 hours. Avoid stressing the bond until fully cured.

      Storage: Store in a cool, dry place, ideally in a refrigerator at 2°C to 8°C. Do not freeze. Unopened bottles have a shelf life of up to 12 months when stored properly.

      Technical data sheet or safety data sheet Sicomet 40 on request.