Product detailed description

Thomsit Chemoprene for floors

Area of use

Preparation dry, clean, free of cracks and separating agents, strong in tension and pressure according to ČSN 744505. Level out unevenness with a suitable Thomsit leveling compound. Always coat mastic asphalt screeds and non-absorbent substrates with a min. 2 mm thick layer of Thomsit leveling compound. Pay attention to the instructions for use, especially the level of maturity for laying. Porous or excessively absorbent substrates and walls should be coated at least once with Chemoprene Na Podlahy diluted Chemoprene adhesive before gluing. Thinner in a ratio of 2:1 and let dry.

Processing

Apply the adhesive to the dry surface. Apply a thin layer on one side to a larger area with a notched trowel A2, A3 or roller and press the glued covering into the adhesive layer so that the back of the covering is wetted. When gluing corks, stair profiles and skirting boards, when gluing to walls and ceilings, the adhesive is applied to both surfaces to be glued on both sides. Mix the adhesive well before use. Let the applied layer of adhesive air out for about 10 minutes, then place the glued part and press firmly. The adhesive must be completely aired out, no adhesive residue should stick to your fingers when you touch them! After reaching the final strength, you can start any further processing of the floor.

Don't miss it!

We recommend not mixing the new formula of Chemoprene Na Podlahy with the original formula. Use only Pattex Chemoprene Diluent for dilution! The ventilation time and open time depend on the temperature and relative humidity of the air. They shorten with rising temperature and falling air humidity, and lengthen with falling temperature and rising air humidity. Observe a max. open time of 10–30 minutes. When gluing over the entire surface, when gluing skirting boards, profiles and on absorbent walls, the open time can be half as long. In this case, apply a thorough primer of the Na Podlahy and Pattex Chemoprene Diluent mixtures (see preparation of the substrate) and let it dry thoroughly. Apply the Chemoprene Na Podlahy adhesive itself to the substrate prepared in this way.

The adhesive must not dry out, otherwise the glued material will partially fall off! Chemoprene Na Podlahy is not suitable for gluing cork boards with PVC treatment on the back (Cork–o–Plast), in this case use Chemoprene Universal or dispersion adhesive Thomsit K 188. Do not store the adhesive for a long time below +6 °C. Do not work with the adhesive at floor temperatures below +6 °C. If the adhesive forms a solid mass or jelly due to low temperatures, allow it to cool freely (not with an open flame) at min. 20 °C back to its original state. The quality of the adhesive remains unchanged. Thick adhesive can be diluted with Pattex Chemoprene Thinner to the desired density. Dilution beyond the original consistency may reduce the bonding effect. This material and its packaging must be disposed of as hazardous waste. Prevent release into the environment. See special instructions on the packaging or safety data sheets.

Cleaning: Immediately after After finishing work with the adhesive, clean the work tools with Pattex Chemoprén Thinner, carefully remove fresh stains on work clothes with petrol. Dried stains on textiles and other contaminated materials can be removed with Pattex Chemoprén Thinner or technical petrol.

First aid: In case of contact with the skin, wash with soap and water, treat with a suitable regeneration cream. In case of contact with the eyes, rinse under running water for about 15 minutes and seek medical attention. In case of ingestion, rinse the mouth, drink 1–2 glasses of water and seek medical attention and show the product packaging. Do not induce vomiting! In case of inhalation, remove the affected person from the contaminated environment.

Technical data

• Colour: beige
• Supply form: thick liquid
• Density:
• Consumption (toothing A2, A3, roller or brush): 200 – 300 ml/m?
• Ventilation time: approx. 10 min.
• Open time: 10. depending on temperature and relative humidity of the air and the amount of adhesive applied
• Loading: immediately
• Final strength after bonding after: 24 hours.
• Suitable for wheelchairs: yes storage: from +6 °C to +25 °C
• Resistance to cleaning: yes
• Thermal resistance of the bonded joint after hardening: max. +70 °C
• Total organic carbon (TOC) content: 0.58 kg/kg of product
• Organic solvent content (VOC): 0.79 kg/kg of product
• Volume content
• Labels according to the Dangerous Substances Regulation: F = highly flammable, Xi = irritant, N = dangerous for the environment